Response time:less than 0.5s
Multifunctional digital thermostat temperature controller made in China
1. Product Highlights
Thermocouple: T, R, J, B, S, K, E, Wre3-Wre25.
Thermo Resistor: Pt100, Cu50.
1 Relay output, 1 SSR controlled output.
Time proportional PID controlled output to either Relay or SSR
Three built-in algorithms that fit most control objects and various applications.
Temperature can be set to display in either Fahrenheit or Celsius degrees.
Supply voltage: 12V AC or DC
Power consumption: < 2 Watts.
Sampling speed: 4/sec.
SSR activated voltage: open circuit: 10V; short circuit: 40mA.
Accuracy: 0.2% of full scale.
LED Display: Red, 0.28 inch
Out of range indication: EEEE.
Ambient temperature requirements: 0 to 50 C (32 to 122 F)
Humidity requirement: < 85% RH.
Relay Contact: 220VAC, 3A.
Controller dimensions: 48 x 24 x 75 (mm).
Opening for installation: 44 x 20 (mm)
3. Panel Illustration and Description
1 -- AL, Relay J1 Indicator.
2 -- Select next parameter / value increment.
3 -- Selection previous parameter / value decrement.
4 -- Digit select / Auto tuning.
5 -- Setting / Confirm.
6 -- Output, controlled output indicator. (AT) Blinking during auto-tuning process.
7 Temperature reading, degrees F or degrees C (as chosen)
4. Parameter Setting
a) Press (SET) to enter setting mode.
b) Press (>), (v) and/or (^) to enter and select parameters.
c) Press (SET) again to confirm entry or selection.
i.) To enter initialization parameter setting mode press (SET), then enter code 0089, press
Table 1 - Initialization Parameters
Temperature Sensor Type
See table 2
Method of controlled
-100 to +100
degrees F, C
Heating = 0;Cooling = 1
Celsius =0;Fahrenheit = 1
Table 2 - Temperature Sensor T ype
-270 ~ 400 C
-50 ~ 1768 C
-210 ~ 1200 C
0 ~ 2300 C
0 ~ 1820 C
-50 ~ 1768 C
-270 ~ 1372 C
-270 ~ 1000 C
P100 Thermo Resistor
-2.000 ~ 6.000 C
Pt100 Thermo Resistor
-200 ~ 600 C
Cu50 Thermo Resistor
-500 ~ 1500 C
0: Relay J1 Alarm output; SSR Disabled, normally used for upper lower limit alarm trigger control.
1: Relay J1 PID controlled output: SSR Disabled. Contact controlled output.
2: Relay J1 as alarm output; SSR PID controlled 12 Volt output. No Contact controlled output.
This controller has 3 types of auto-tuning control methods already built-in:
0: Universal PID control suitable for increase/decrease fast speed of change of temperature
1: Gradual change PID control is suitable for applications that require steady change of
temperature and speed of temperature change is not critical.
2: Fuzzy logic control suitable for system with oscillation and sensing signal delay.
ii.) To enter the PID parameter setting mode, press (SET), then enter code 0036, press (SET)
Table 3 - PID and Relevant Parameters:
0.1 ~ 99.9 (%)
2 ~ 1999 (Sec)
0 ~ 399 (Sec)
1 ~ 999 (Deg)
On/Off Control Range
1 ~ 999 (Deg)
2 ~ 199 (Sec)
0 ~ 3
P, I, and d parameters control the accuracy and response time of the temperature controller. Autotuning
is recommended for users who are not familiar with PID control theory. P, I and d values
should only be adjusted by professionals.
Proportional Band (P): When P increases, fluctuation of object being controlled decreases. When P
decreases, fluctuation of object being controlled increases. When P value is too small, system may
Integration time (I): its purpose is to reduce static error. When I decrease, respond speed is faster but
system is less stable. When I increase, response speed is slower, but system is more stable.
Differentiation time (d): its purpose is to control in advance and compensate delay. Setting d-value
too small or too large would decrease system stability, oscillation or even non-converge.
Integration control range (SF): It defines integration range limits. When |SV-PV|
control is activated.
Full power/complete off range (bb): It defines temperature range limits that the heating/cooling
element is either fully on or fully off. When |SV-PV|>bb, heating/cooling element could be either full
power heating or complete not power.
Control Period (ot): As ot is set lower, the heating/cooling cycle is driven faster, and thus system
responce speed is faster. When using contact control (Relay), the mechanical contacts will wear out
When contact control (Relay) is used, normally set ot = 5~30.
When non-contact control (SSR) is used, normally set ot = 2.
Digital Filtering (Filt): Filt=0, filter disabled; Filt=1, weak filtering effect; Filt=3, strongest filtering
effect; Stronger the filtering, more stable the readout, but has more readout display delay.
iii.) To enter temperature and alarm parameter setting mode, press (SET), then enter code
0001, press (SET) a gain.
Table 4 - Temperature Setting and Alarm Related Parameters:
Within testing range
Within testing range
Within testing range
Figure 4 Figure 5
iv.) During Normal Operation mode, pressing (^) or (v), the display will show SV.
Pressing (^) or (v) again would increase or decrease SV by 1 degree.
a) Set AH1 = AL1, relay is disabled.
b) Set AH1 > AL1: Normally used for upper limit alarm trigger. See Figure 4.
c) Set AH1 < AL1: Normally used for lower limure 5.
By simply pressing a single button, the built-in artificial intelligent is activated to automatically
calculate and set parameters ( P, I, d, SF, Bb, Ot ) that fit the condition to be controlled.
a) How to start and stop the auto-tuning process:
i. To activate auto-tuning, press and hold (>) until AT indicator blinks, which indicates autotuning
is in progress. When auto-tuning finishes, the AT indicator light turns off. Now newly
calculated PID parameters are stored in memory and will be used by the controller.
ii. To EXIT during the auto-tuning process, press and hold (>) until AT indicator turns off.
The previously entered PID parameters values are used by the controller.
Connection Terminals (back view).
Note that the polarity of power at terminals 1 and 2 does not matter.
1 how to pay ?
T/T PAYPAL WESTUNION
2 when will you arrange the produce ?
Within 12 hours once we get the payment
3 what is your main products ?
Thermocouple ,PT100 sensor ,termperture controller ,infared thermometer and son on .
4 what is the quality of your products ?
Can offer ISO9001,CE,ROHS,SGS and other certificates .
5 what kind of informations shall i give you regarding the shipping ?
Company name ,Recipients, Correct Address , telephone ,zip code
6 what is your warranty ?
For most of our products ,the warranty will be 12 monthes .
7 when will i get a solution for defective products ?
Within 48 hours (on working days )
8 what is your shipping method ?
DHL,FEDEX,UPS,TNT,EMS,CHINA POST AIR ,SEA FREIGHT and AIR FREIGHT !
9 what is your shipping time ?
For General Orders ,the shipping time will be 5 workdays .
Hello, please leave your name and email here before chat online so that we won't miss your message and contact you smoothly.