loading

Expert Thermocouple & RTD &Temperature Sensor Manufacturer.

Introduction to general regulations for the production of ventilation ducts

General requirements for ventilation duct production? It can be said that each level has certain requirements, and it can also be mastered from the basic raw material level. Then you can take into account the detailed information on its installation and other aspects, and you must master the installation of ventilation ducts. Now, let’s take a look at Zhangjiagang Jinrong Ventilation and I believe it will help you to some extent. 1. Before the production of ventilation ducts, it is necessary to check whether the selected raw materials meet the relevant quality regulations, and whether there are compliance management qualification certificates or quality mark documents. In the absence of relevant documents, the court inspection shall meet the following requirements: (1) The surface layer of the selected board must be smooth and uniform in thickness, without cracks, sand holes, scars, edges and rust. (2) As far as this type of fabric air duct sheet is concerned, there must be no cracks, air bubbles, holes and other defects that endanger the quality of the fabric air duct sheet. (3) The selected other raw materials should not cause the compressive strength of the finished product to be reduced or endanger the high efficiency of its application due to defects. 2. For the ventilation duct pipe layer, the surface layer should be leveled, the arc shape should be well-proportioned, and the longitudinal seams should be overlapped. In addition, the occlusion of the teeth should also be close and the overall width should be symmetrical. The appearance of welding should be checked, and there should be no defects such as porosity, sand, slag, and cracks. 3. Regarding the production of metal material ventilation ducts and spare parts, the allowable error of the diameter or outer length of the ventilation duct is: -1mm for less than or equal to 300mm, -2mm for more than 300mm, in which the annular flange is The allowable error of the inner diameter or the inner side of the rectangular frame flange is +2mm, and the unevenness cannot exceed 2mm. 4. All right-angle turns in the air duct system software should be installed with sound-absorbing bends and galvanized iron sheet drainage sheets. 5. The insulation layer of the air duct must be made of polyethylene insulation foam board. The joint part of the edge of the thermal insulation layer should use a ladder or tongue and groove structure, and use epoxy resin to carry out adhesion. 6. The mechanical equipment selected for the air duct should be pressed groove, the air duct should be processed neatly and tightly, and the surface layer in the socket should be covered with structural glue. 7. For the tight connection between the air duct and the air outlet, a plastic hose with an insulating layer must be used for connection. To sum up, I firmly believe that everyone has a certain grasp of the production of ventilation ducts.

is emerging as one of the most popular resistance temperature detector, moving beyond its RTD supplier benefits, with conclusive scientific evidence suggesting the positive role play in temperature sensor manufacturers.

We would like to offer our comprehensive service to our customers who interested in temperature sensor.

A wholesaler should have many RTD supplier based products that could help you if you have a temperature sensor manufacturers problem. It is better to treat the problem early rather than have to deal with it later. Shanghai Jiutian Automation Equipment Co., Ltd is your best choice.

GET IN TOUCH WITH Us
recommended articles
NEWS
At present, more and more customers on the market are just beginning to attach great importance to the hidden dangers of the application of air disc machines and equipment.
Ventilation duct manufacturers talk about three welding methods for fabric ducts: Method 1: Manual welding.
It should be erected by the scaffolder according to the special safety construction organization design (construction plan) or safety technical measures.
Compliance Standards and Common Problems in Ventilation Duct Equipment Many bosses generally ignore the smoke exhaust system and natural ventilation planning of the restaurant kitchen when they open a new restaurant, which eventually leads to the closure of the hotel for renovation, renovation or sale of serious losses.
Ventilation pipe ventilation pipe manufacturer is a hollow pipe used for ventilation.
When we want to enter an industry and decide to dedicate our light and heat, our calm choice is to analyze this market well.
How to ensure the construction quality of dust removal fabric duct ventilation duct? In order to promote the construction of dust-removing fabric duct ventilation ducts, we should formulate some drastic measures.
How does the ventilation duct manufacturer ensure the construction quality of the ventilation duct for the dust removal fabric duct? 1.
There are common pipes everywhere in daily life, and it is not clear what to do.
Ventilation ducts are metal or composite ducts for ventilation in industrial and civil buildings.
no data

CONTACT DETAILS

Phone: +86 13816377866
Email: jimmy011@126.com
Add:NO999, Sunqiao RD, Pudong area, Shanghai, China
 

CONTACT US FOR FREE SAMPLE !

For more products related question ,Welcome to inquiry us .

Copyright © 2019 Shanghai Jiutian Automation Equipment Co., Ltd. | Sitemap
Customer service
detect