+86 13816377866 | 
jimmy011@126.com
Vietnamese customers come to visit our factory
Thermocouple head
Thread single-head thermocouple installation
by：JVTIA
2020-11-12
A, install single head thread thermocouple overview
thread single-head thermocouple installation structure: in a single head of thermocouple wire welding with a hex head ( For fastening) Size range, Be determined by the customer) The male ( British) The hollow bolt. And can be divided into hex head up and down two.
use: widely used in all kinds of heating liquid material that can withstand pressure acuity 0. 8Mpa。
recommended specifications: 8 x 60 ︿ ︿ 20 1000
2, thread strength of single thermocouple head of electrical installation
the influencing factors of thermocouple electric strength mainly include the thickness of the insulation, insulation quality of raw material, the length of the thermocouple, bending radius and the number of bending.
3, install single-head screw thermocouple used
1, uniform heating air element should cross arranged, make the element has good heat dissipation conditions, make the air flow can be fully heated.
2, connection parts should be on the outside of the insulation layer, avoid contact with corrosive, explosive medium, water.
3, lead connection should be able to long-term bear part of the temperature and heating load, connection screw fastening should avoid too hard.
4, thermocouple wire the magnesium oxide powder, the use place to avoid contamination and moisture infiltration, prevent leakage accidents.
4, install single head thread thermocouple order information
1. Heater voltage, power, phase number, lead wire length;
2. Heating pipe length, width, diameter, flanged to provide flange outer diameter, thickness, hole number, etc. ,
3. Thermocouple material requirements, flange material, whether to need protection, etc.
five Suggestions, thermocouple surface load values
the following surface load refers to cooperate with metal mould heating, water heating can be multiplied by 2 ~ 2. 5. Air heating is 50% ~ 60%
diameter load values ( Wcm square)
φ6～φ10 ≤22
φ10. 1 ～φ14 ≤20
φ14. 1～φ18 ≤16
φ18. 1～φ22 ≤12
φ22. 1 ~ phi 40 10 or less
our company also supply the products of similar products: heaters, thermocouple, flange thermocouple
thread single-head thermocouple installation structure: in a single head of thermocouple wire welding with a hex head ( For fastening) Size range, Be determined by the customer) The male ( British) The hollow bolt. And can be divided into hex head up and down two.
use: widely used in all kinds of heating liquid material that can withstand pressure acuity 0. 8Mpa。
recommended specifications: 8 x 60 ︿ ︿ 20 1000
2, thread strength of single thermocouple head of electrical installation
the influencing factors of thermocouple electric strength mainly include the thickness of the insulation, insulation quality of raw material, the length of the thermocouple, bending radius and the number of bending.
3, install single-head screw thermocouple used
1, uniform heating air element should cross arranged, make the element has good heat dissipation conditions, make the air flow can be fully heated.
2, connection parts should be on the outside of the insulation layer, avoid contact with corrosive, explosive medium, water.
3, lead connection should be able to long-term bear part of the temperature and heating load, connection screw fastening should avoid too hard.
4, thermocouple wire the magnesium oxide powder, the use place to avoid contamination and moisture infiltration, prevent leakage accidents.
4, install single head thread thermocouple order information
1. Heater voltage, power, phase number, lead wire length;
2. Heating pipe length, width, diameter, flanged to provide flange outer diameter, thickness, hole number, etc. ,
3. Thermocouple material requirements, flange material, whether to need protection, etc.
five Suggestions, thermocouple surface load values
the following surface load refers to cooperate with metal mould heating, water heating can be multiplied by 2 ~ 2. 5. Air heating is 50% ~ 60%
diameter load values ( Wcm square)
φ6～φ10 ≤22
φ10. 1 ～φ14 ≤20
φ14. 1～φ18 ≤16
φ18. 1～φ22 ≤12
φ22. 1 ~ phi 40 10 or less
our company also supply the products of similar products: heaters, thermocouple, flange thermocouple
Custom message
Related Products
